1000L PV- Module Temperature Humidity Chamber / Solar Damp Heat Cycle Test Chamber
OEM and ODM are welcome
Application :
Solar/photovoltaic module constant temperature and humidity test chamber/solar/photovoltaic module
high/low temperature damp heat cycle test chamber is an essential test equipment mainly used in
photovoltaic industry and solar energy industry. It is used to test photovoltaic modules, mainly
monocrystalline silicon modules, ground The use of crystalline silicon photovoltaic modules, ground thin
film photovoltaic modules and other series of shut-off parts for high temperature, low temperature,
alternating heat and humidity or constant temperature and environmental changes in the test parameters
and performance; or constant humidity heat test temperature environment changes Parameters and
performance. Applicable to schools, factories, military, research positions, and other units .
Specification
| Capacity(L) | 1000L
|
Temperature range | -40 °C ~ 100 °C |
Humidity range |
20%~98%R·H(40~90°C) (controllable and adjustable) |
Alternating humidity |
75%~95%R·H(25~85°C)
|
Temperature fluctuation | ≤ ± 0.5 °C
|
Temperature deviation: |
≤ ± 2 °C |
Humidity deviation | +2,-3%R·H |
Heating and cooling rate | 1.0 ~ 3.4 °C / min (linear adjustable)
|
The time range | 0~9999H adjustable
|
Power supply | 380V 50Hz
|
Photovoltaic module constant temperature and humidity test chamber meets
1. GB/T 19394.-2003 test;
2. GB/T9535.-1998 test;
3. GB/T6492-1986, GB/T6494,
4.GB/T6497, SJ/T2196;
5.IEC61345-1998; IEC61646,
6. IEC61215, etc. National standards, as well as other relevant standards.
7. Strictly according to GB 10592-89 "Technical Conditions for High and Low Temperature Test Chambers
8. GB 10586-89 "Damp Conditions for Hot and Cold Test Chambers" for design and manufacture,
9. Conforms to IEC61215-2005 temperature. The corresponding standard parameters for damp heat can
be used for various high and low temperature heat and humidity alternating environments.
10. Solar Solar: IEC61215, UL1703, GB9535
11.Thin-film solar energy: IEC61646, GB18911
Main Material List imported from famous brand
Name | Brand
|
Compressor | French Tecumseh
|
Oil separator | American Emerson, ALCO, Temprite
|
Plate heat exchanger | GEA, Xingsuneng, Guoxing
|
press switch | Denmark DANFOSS, Saginomiya
|
Condenser | Guangzhou Yongqiang, Klean Air
|
Evaporator | Yongqiang
|
Dry filter | Denmark DANFOSS, USA SPORLAN
|
Capillary tube | KOMEG
|
Expansion valve | Denmark DANFOSS, USA SPORLAN
|
Magnetic valve | Japan SAGLNOMLYA
or Nickideu /
Denmark DANFOS |
Controller | KOMEG
|
Residual current circuit breaker | Taiwan SHIHLIN
|
No-fuse switch | French Schneider
|
AC contactor | Japan French Schneider
|
Features
Photovoltaic module constant temperature and humidity test chamber meets the test index
1. Thermal cycle test
Photovoltaic modules circulate between -40°C±2°C and 85°C±2°C in a test space where the wind speed
is not less than 2m·S-1.
2. Wet - cold (frozen) test
Place the PV module in the environmental chamber at room temperature and complete 10 cycles. The
maximum and minimum temperatures shall be within ±2°C of the set value, and at any temperature above
room temperature, the relative humidity shall be maintained within ±5%R·H of the set value.
Photos show
Product Tags:
|
|
1000L PV- Module Temperature Humidity Chamber / Solar Damp Heat Cycle Test Chamber Images
|
