1. Brief Introduction
It can determine the corrosion resistance of iron metal or the iron metal inorganic film or organic film test, such as: electroplating, anode processing, conversion coating, painting, ect.
Design standards:
CNS3627,3885,4159,7669,8886,JIS D-0201,H-8502,H-8610,K-5400, Z-2371,ISO 3768,3769,3770,ASTM B-117,B-268,GB-T2423,GJB 150.
2. Features you need to know, If you are new to Salt Spray Tester:
1.LCD display and a pid controller or touch screen programmable controller.
2.Entire PVC sheet material, the internal ring with the use of advanced three-dimensional flutter high technology products, strong structure, fresh, never deformation and acid and alkali, high temperature and never aging, for salt spray, copper acetate, and other test specifications.
3.Controller are in the same panel, the operation simple and clear.
4.Neutral salt spray (NSS), acetic acid salt spray ( AASS ), copper accelerated salt spray ( CASS ) either of the test laboratory
3. Main Technical Parameter:
| Specifications (Note: We reserve the right to change specifications without prior notice) |
| Model | HL-160-NS | HL-120-BS | HL-90-BS | HL-60-SS |
| Interior dimensions(W*H*D)mm | 1600 X 500 X 1000 | 1200 X 500 X 800 | 900 X 500 X 600 | 600 X 400 X 450 |
| Exterior dimensions(W*H*D)mm | 2240 X 1500 X 1600 | 1410 X 1280 X 880 | 1460 X 1280 X 910 | 1130 X 1070 X 630 |
| Testspace Volume(L) | 800 | 480 | 270 | 108 |
| Salt Water Tank Volume (L) | 60 | 40 | 25 | 15 |
| Heater | 15KW+1KW | 11KW+1KW | 7KW+0.75KW | 3KW+0.75KW |
| Air compressor | 2HP | 2HP | 1/2HP | 1/2HP |
| Temp. range (Testing barrel) | 35±1℃～50±1℃ |
| Temp. range (Pressure barrel) | 47±1℃～63±1℃ |
| Test applicable | NSS, ACSS,CASS,CORK |
| Pressed Air Pressure | 1.00±0.01kgf/cm² |
| Spray Amount | 1.0~2.0ml/80cm²/h(Collect at least 16 hours, take the average) |
| Ambient Relative Humidity | More than 85%R.H. |
| PH Value | 6.5~7.2 3.0~3.2 |
| Spraying Manner | Programmable Spraying |
| Power | AC220V 1Φ 50Hz |
4. Know the following Typical coatings that can be evaluated with this method are:
1) Phosphated surfaces (with subsequent paint/primer/lacquer/rust preventive)
2) Zinc and zinc-alloy plating (see also electroplating). See ISO 4042 for guidance
3) Electroplated chromium, nickel, copper, tin
4) Coatings not applied electrolytically, such as zinc flake coatings according to ISO 10683
5) Organic coatings
6) Paint Coating
1. Dry-bulb thermometer
2. Wet-bulb thermometer
3. Hopper
4. Hopper protecting cover
5. Laboratory cover
6. The water inlet of salt water supplement
7. Operating panel
8. Saturated barrel water inlet
9. Pressure regulating valve
1. Exhaust port
2. The drain port
3. The drain valve
4. Air inlet
5. Power line 220v single
